The flow regulator DN 15, 1/2" is suitable for the NEOMERIS Softmaster RS.

The flow regulator DN 25, 1" is suitable for the NEOMERIS Softmaster RS.

The flow regulator DN 40, 1 1/2 " is suitable for the NEOMERIS Softmaster RS.

The flow regulator DN 50, 2" is suitable for the NEOMERIS Softmaster RS.

The flow regulator DN 65, 2 1/2" is suitable for the NEOMERIS Softmaster RS.

The flow regulator DN 80, 3" is suitable for the NEOMERIS Softmaster RS.

The instrument is used for conductive measurement / control of the electrolytic conductivity, the resistivity or the TDS value. In addition, the JUMO AQUIS 500 CR offers the possibility of displaying the measured conductivity according to a customer-specific table. display.Both conductive two-electrode and four-electrode measuring cells can be connected to the device. The temperature measurement is carried out as a second input variable with a Pt100/1000. Depending on the measured variable, specific automatic temperature compensation is possible.The unit is operated via keys and a large LC graphic display. This display makes it easy to read the measured value. The display of the parameters in plain text simplifies configuration for the operator and supports correct programming of the unit.The modular design of the unit allows it to be adapted to the requirements of the application. Up to four outputs are available.Typical areas of application:Universally applicable in water and wastewater management, service water, process water and wastewater, drinking, well and surface water, pure and ultrapure water applications, pharmaceutical water applications (e.g. according to USP, Ph.Eur., WFI), water quality measurements, TDS measurements (ppm or mg/l).Special features Direct switching option to specific      - specific conductivity (µS/cm or mS/cm)      - specific resistance (kΩ x cm or MΩ x cm)      - TDS measurement (ppm or mg/l)      - customer-specific tableAutomatic temperature compensation: off (e.g. USP), linear, ASTM, natural waters (EN 27888/ISO 7888)Large LC graphic display with backlightingDisplay presentation selectable: large digits, bargraph or tendency displayCalibration options depending on measured variable: cell constant and temperature coefficientCalibration logbookConnection possibility of two-electrode measuring cells (standard) or four-electrode measuring cellsActivatable contamination detection Autorange operation Protection class IP67 for surface mounting Protection class IP65 for control cabinet mountingOperator languages switchable: German, English, French; other languages via setup program RechargeableThrough setup program: convenient programming, system documentation, Loading of further operator languages

Version 2: stock version: type 202560/20-888-000-310-000-23/000 ; part-no. 00480050 The unit is used for measuring/controlling the pH-value, the redox-voltage or the NH3-(ammonia)-concentration. The function can be switched directly on the unit. Depending on the measurand, combination electrodes (e.g. pH/redox combination electrodes, gas-sensitive sensors) or separate versions (glass/metal electrodes with separate reference electrode) can be connected. The second input variable is the temperature measurement, which can be carried out with a Pt 100/1000, for example. Automatic temperature compensation is thus possible for the measured variables pH value and NH3. The units are operated via clear keys and a large LC graphic display. This display enables good readability of the measured value. The display of the parameters in plain text makes configuration easier for the operator and supports correct programming of the unit. The modular design of the unit allows it to be adapted to the requirements of the application. Up to four outputs are available. Special features   direct switching option for pH value, redox voltage or NH3 (ammonia) concentration Automatic temperature compensation Large LC graphic display with backlighting Display selectable: large digits, bar graph or tendency display Solderless connection technology - Calibration options depending on measurand one/two/three-point calibration calibration logbook Impedance measurement can be activated for pH measurement Asymmetrical and symmetrical connection of pH sensors Possibility of connecting pH ISFET sensors through integrated output for sensor power supply Protection class IP67 for surface mounting, protection class IP65 for control cabinet mounting User languages switchable German, English, French; further languages can be loaded via setup program Through setup program: convenient programming, system documentation, reloading of further user languages

Indicator/controller for digital sensors with Modbus protocolThe unit has 1 digital interface, 1 analogue temperature input and 1 binary input. The digital interface is suitable for connecting sensors that have a Modbus RS485 interface. If the connected sensor does not have an integrated temperature sensor, a resistance thermometer Pt100, Pt1000 or NTC/PTC (up to 4 k) can be connected to the analogue temperature input. The power supply for the digital sensor is integrated in the unit.The LCD graphic display allows the input signals to be shown as digits or as a bar graph. The display of the parameters in plain text makes operation easy to understand and safe.With two optional relay change-over contacts, both simple switching or alarm functions and sophisticated control tasks with P, PI, PD and PID behaviour can be realised. On request, the unit can also be supplied with two freely parameterisable and scalable analogue outputs (0 to 10 V, or 0(4) to 20 mA).Special featuresDisplay: mg/l, ppm, % SAT, %, ‰, g/l, ppb, µg/l, NTU, FNU, etc.Special displays are also possible with the setup programmeLarge LCD graphic display with backlightingDisplay representation selectable: large digits, bargraph or trend displayIntegrated calibration routines:depending on the sensor: zero point, full scale and 2-pointCalibration logbookProtection class IP67 for surface mountingProtection class IP65 for control cabinet mountingOperator languages (switchable): German, English, Frenchthrough setup program (option): convenient programming, system documentation, reloading of additional operating languages

Typical areas of applicationProcesses with higher continuous temperatures (up to a maximum of 135 °C)Sterilisation applicationsDouble chamber design in the presence of electrode poisonsfluoride-containing (hydrofluoric acid-containing) media up to 1000 mg HF/lSpecial featuresproven JUMO HT glass (pH high-temperature membrane glass) 0 ... 14 pHJUMO DS membrane glass for sterilization applicationsCartridge discharge system with silver ion-free reference electrolyte (gel)Pressure-resistant versions up to 10 bar (50 °C)Temperature range: 0 ... 135 °C1Temperature sensors can be integrated as an optionORP versions with platinum or gold cap up to ±2000 mV

Typical areas of applicationProcesses with higher continuous temperatures (up to a maximum of 135 °C)Sterilisation applicationsDouble chamber design in the presence of electrode poisonsfluoride-containing (hydrofluoric acid-containing) media up to 1000 mg HF/lSpecial featuresproven JUMO HT glass (pH high-temperature membrane glass) 0 ... 14 pHJUMO DS membrane glass for sterilization applicationsCartridge discharge system with silver ion-free reference electrolyte (gel)Pressure-resistant versions up to 10 bar (50 °C)Temperature range: 0 ... 135 °C1Temperature sensors can be integrated as an optionORP versions with platinum or gold cap up to ±2000 mV

Capacity measurement ion exchanger cartridgeOur Neomeris N-FLASH10 conductivity meter in a T-piece with 3/8 inch connection is a conductivity measuring instrument that is used to monitor the electrical conductivity of water after flowing through the ion exchanger cartridge. The measuring instrument including the integrated measuring cell is battery operated and permanently installed in the T-piece. If the measured electrical conductivity is below the limit value of 10µS/cm, the green LED flashes; if it is above, the red LED flashes, indicating that a cartridge or resin change is required. Due to the T-piece used, the measuring device can also be integrated very easily and is optimally installed in the liquid flow for a stable measurement. Measuring principle: The measuring cell generates an electrical signal that is proportional to the conductivity of the liquid. This signal is processed in the device and the LED is controlled via the programming stored in the device. Application: Conductivity meters are often used in water treatment plants in the process industry.Technical data:Screw-in thread: 3/8"; others available upon requestMaterial housing: POM black Material lid: Plexiglas Material electrodes: V4A 4571 Material O-ring: EPDM Cell constant: C= 0.6 +/- 10% Max. Operating pressure: 6 bar Max. Operating temperature: 60°C Temperature sensor: without Display: LED green <10μS/cm LED red >10μS/cm

Technical data: Screw-in thread: 1/4"; 1/2"; 3/4"; others available upon requestMaterial housing: POM black Material lid: Plexiglas Material electrodes: V4A 4571 Material O-ring: EPDM Cell constant: C= 0.6 +/- 10% Max. Operating pressure: 6 bar Max. Operating temperature: 60°C Temperature sensor: without Display: LED green <10μS/cm LED red >10μS/cm

Technical data: Screw-in thread: 1/4"; 1/2"; 3/4"; others available upon requestMaterial housing: POM black Material lid: Plexiglas Material electrodes: V4A 4571 Material O-ring: EPDM Cell constant: C= 0.6 +/- 10% Max. Operating pressure: 6 bar Max. Operating temperature: 60°C Temperature sensor: without Display: LED green <20μS/cm LED yellow 20-50μS/cm LED red >50μS/cm

Technical data: Measuring range: 0 - 10 μS/cm (without temperature compensation) <0.1 <0.5 < 1.0 < 5.0 < 10 μS/cm LED display: 3x green; 1x yellow; 1x red Power supply: 100-240 VAC plug-in power supply unit Energy consumption: < 500 mWHousing material: POM black (polyoxymethylene) Viewing window material: PMMA (acrylic glass) Electrodes: Stainless steel 1.4571 Dimensions: Diameter 40 mm x 68 mm (Top) / 110 mm (Total) Gasket electrodes: EPDM Gasket housing: EPDM Application limits: Pressure max.: 6 bar; Temperature max.: 60 °C Protection class: IP 65* Display           Measuring range 3 LED green < 0.1 μS/cm 2 LED green < 0.5 μS/cm 1 LED green < 1.0 μS/cm 1 LED yellow < 5 μS/cm 1 LED red < 10 μS/cm 1 LED red flashing ≥ 10 μS/cm

Technical data:Measuring Range: 0 - 20 uS/cm (without temperature compensation)<1,0 <5,0 < 10,0 < 20,0 > 20,0 uS/cmLED-Display: 3x green; 1x yellow; 1x redVoltage Supply: 100-240 VAC with wall plug transformerPower Consumption: < 500 mWHousing: POM black (Polyoxymethylen)Vision Panel: PMMA (Acryl Glass)Electrodes: Stainless Steel 1.4571Dimension: Diameter 40 mm x 68 mm (Top) / 110 mm (Total)Seals Electrodes EPDMSeal Housing: EPDMOperation Limits: P max: 6 bar; T max: 65 °CProtection Class: IP 65*Display            Measuring value3 LED green <= 1,0 uS/cm2 LED green < 5,0 uS/cm1 LED green < 10,0 uS/cm1 LED yellow < 20,0 uS/cm1 LED red flashing >= 20,0 uS/cm

Device for measuring the electrical conductivity of aqueous solutions in conjunction with an integrated two-electrode screw-in measuring cell 3/4 inch without temperature compensation. The devices are selected according to the respective measuring range and are available as a variant with or without potential-free relay output.Application examplessoftener cartridgescomplete desalinationreverse osmosisAdded valueOperation at 9 V DC via supplied plug-in power supply1 potential-free relay with switchable mode of operation of relay controlLimit value display optically by means of LEDs   Technical dataMeasuring ranges: 0 - 10 / 100 / 1000 μS/cm, depending on instrument typeLimit value displays: Optical by means of LEDs, limit values adjustable between 0 and 100 % of the measuring range 1 potential-free relay contact, max. 2 A / 250 V AC, 60 W / 62.5 VA (if selected) Power supply: 9 V DC via plug-in power supply unit 100 - 240 V AC Power consumption: approx. 1 W Protection class: IP 65 Housing: polycarbonate housing, 82 x 60 x 57 mm Connections: side connection for plug-in power supply and one relay output (if selected) Measuring cell: ¾", PP, PN 6, Tmax. 60°C

Device for measuring the electrical conductivity of aqueous solutions in conjunction with an integrated two-electrode screw-in measuring cell 3/4 inch without temperature compensation. The devices are selected according to the respective measuring range and are available as a variant with or without potential-free relay output.Application examplessoftener cartridgescomplete desalinationreverse osmosisAdded valueOperation at 9 V DC via supplied plug-in power supply1 potential-free relay with switchable mode of operation of relay controlLimit value display optically by means of LEDs   Technical dataMeasuring ranges: 0 - 10 / 100 / 1000 μS/cm, depending on instrument typeLimit value displays: Optical by means of LEDs, limit values adjustable between 0 and 100 % of the measuring range 1 potential-free relay contact, max. 2 A / 250 V AC, 60 W / 62.5 VA (if selected) Power supply: 9 V DC via plug-in power supply unit 100 - 240 V AC Power consumption: approx. 1 W Protection class: IP 65 Housing: polycarbonate housing, 82 x 60 x 57 mm Connections: side connection for plug-in power supply and one relay output (if selected) Measuring cell: ¾", PP, PN 6, Tmax. 60°C

Device for measuring the electrical conductivity of aqueous solutions in conjunction with an integrated two-electrode screw-in measuring cell 3/4 inch without temperature compensation. The devices are selected according to the respective measuring range and are available as a variant with or without potential-free relay output.Application examplessoftener cartridgescomplete desalinationreverse osmosisAdded valueOperation at 9 V DC via supplied plug-in power supply1 potential-free relay with switchable mode of operation of relay controlLimit value display optically by means of LEDs   Technical dataMeasuring ranges: 0 - 10 / 100 / 1000 μS/cm, depending on instrument typeLimit value displays: Optical by means of LEDs, limit values adjustable between 0 and 100 % of the measuring range 1 potential-free relay contact, max. 2 A / 250 V AC, 60 W / 62.5 VA (if selected) Power supply: 9 V DC via plug-in power supply unit 100 - 240 V AC Power consumption: approx. 1 W Protection class: IP 65 Housing: polycarbonate housing, 82 x 60 x 57 mm Connections: side connection for plug-in power supply and one relay output (if selected) Measuring cell: ¾", PP, PN 6, Tmax. 60°C

Instrument for measuring the electrical conductivity of aqueous solutions in conjunction with two-electrode measuring cells. Designed as wall-mounted version.Operation at 230 V AC or 24 V DC possible2 potential-free relays - changeover switch for limit value switching (hysteresis 5 % fixed)Alphanumeric display with 2 x 16 charactersTemperature measurement and temperature display from 0.0 °C to 90.0 °C when a Pt100 is connectedSwitchable temperature compensation with 2.2 % / K up to 90 °CMonitoring of the temperature sensor for sensor break and error message on the displaySwitchable mode of operation for relay controlOutput of the measured value with 0 - 10 V and 4 - 20 mA Technical data Measuring ranges: dependent on measuring cell and amplification Temperature compensation: Linear 2.2 % / K, can be switched off, reference temperature 25 °CLimit value displays: Optical by means of 2 LEDs, 2 limit values adjustable over the measuring range Limit value outputs: 1 potential-free changeover contact, max. 6 A / 250 V AC1 change-over contact to 230V AC (terminal 21) Analog outputs: 0 - 10 V, Ra > 1 kOhm; corresponds to 0 - 20 / 200 / 2000 μS/cm 4 - 20 mA, Ra < 500 Ohm; corresponds to 0 - 20 / 200 / 2000 μS / cm Power supply: 22 - 26 V DC, protected against reverse polarity, electrically isolated, 1000 V insulation voltage, or 230 V 50/60 Hz Power consumption: Approx. 3 W / 3 VA Protection class: IP 65 Housing: Surface-mounted housing (polycarbonate) 120 x 122 x 57 mm Connections: 4 x M16 cable entries on the bottom of the housing.

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. Standard LED configuration (1 green LED, 1 red LED): <1500 µS/cm = green >1500 µS/cm to <1900µS/cm = green/red flashing >1900 µS/cm = red Technical data: Measuring range: 0 - 2000 μS/cm Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-2000 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: 3/4" Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter for conductivity monitoring Our innovative conductivity meter has been specially developed for monitoring conductivity in ultrapure water (demineralised water) and has a 4-20 mA signal output that enables easy integration into higher-level control systems.The measurements are temperature-compensated, which ensures greater accuracy. With a measuring range of 0 to 2 µS/cm, our device is particularly suitable for monitoring low conductivities, such as those typically found in mixed-bed ion exchanger cartridges. The limit value is displayed by means of 2 LEDs (green/red) on the top of the device. An acrylic glass cover ensures that the current status is immediately visible. The device has a ¾ screw thread, which can be customised for easy and safe installation. There is also the option of customisation in terms of the LEDs, including the measuring range and a private label. Our high-quality conductivity meter offers a reliable solution for conductivity monitoring in medical areas to fulfil the guidelines and recommendations of the DGSV. Our measuring device is also particularly suitable for mixed bed cartridge monitoring in the clinical environment. Standard LED configuration (1 green LED, 1 red LED): <0.5 µS/cm = green >0.5 µS/cm to <1.0 µS/cm = green/red flashing >1 µS/cm = red

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. Standard LED configuration (1 green LED, 1 red LED): <20 µS/cm = green >20 µS/cm to <40µS/cm = green/red flashing >40 µS/cm = red Technical data: Measuring range: 0 - 50 μS/cm Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-50 μS/cm Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: according to your requirements Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*

High-quality conductivity meter with a 4-20mA signal output for forwarding the measured value to a higher-level control system, for example. The measurement is temperature compensated and therefore offers you an accurate measurement result. Also here we have the possibility to offer you an individual design regarding the connection, the LEDs including the measuring range up to a private label.  Due to the acrylic glass cover used, the light of the LEDs is widely scattered and the current LED status can be seen from a distance in darker rooms.  Quality Made in Germany. Standard LED configuration (1 green LED, 1 red LED): <20 µS/cm = green >20 µS/cm to <40µS/cm = green/red flashing >40 µS/cm = red Technical data: Measuring range: according your requirements Temperature compensation: Linear 2.2 % / K, reference temperature 25°C Accuracy conductivity: +/-10% of the maximum full scale value Accuracy temperature: +-1.0 °C Limit value display: Optical via LED Analog output: 4-20 mA = 0-... μS/cm (according your needed measuring range) Power supply: 24 VDC +-10% Power consumption: < 2.5W Screw-in thread: 3/4" Housing: POM (polyoxymethylene) Vision panel: PMMA (acrylic glass) Electrodes: stainless steel 1.457 Dimensions: Diameter 60 mm x 60 mm (top) / 100 mm (total) Gaskets electrodes: EPDM, 28 x 3 mm Gasket housing: EPDM, 50 x 2 mm Application limits: P max: 6 bar; T max: 50 °C Protection class: IP 65*